• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A damaged window pane could be a source of frustration. It could also be a chance to upgrade your glass to energy-efficient or insulated windows and reap benefits like more comfort, higher the value of resales and lower utility costs.

It's a project you can tackle yourself at only a fraction of the cost of hiring a professional. You'll only require the right tools and a few hours of your time.

Glass

Replace your old single-paned windows with tempered or insulation glass to improve the efficiency of your energy, reduce noise, and maintain the original character of your home's older. The procedure of replacing windows is easy and can be accomplished by most homeowners who possess basic hand tools. Alongside a replacement pane, the following components are needed for the replacement process: latex glazing putty glazier's points; pliers; and a heat gun for warming the old putty, if needed. Wear safety glasses and gloves prior to starting. Working with broken glass can cause serious injuries.

Take out any broken glass pieces remaining. This is best accomplished with pliers, though using flathead screwdrivers can be effective in the pinch. After that, use a wood chisel or putty knife remove the remaining old putty around the frame and sash. Be careful and slow making sure not to break the current window sash. It is a good idea to do this on a sturdy ladder rather than the ground and to have someone standing below the sash to help hold it steady.

Prepare the window frame to accommodate the new pane after you have removed the old putty. Take measurements of the width and height of the opening in the sash by subtracting 1/8 inch from each measurement (to allow for seasonal expansion and contraction). Bring these measurements to an hardware store or home center and get a piece of stock glass cut to size. You can also cut the glass yourself if you have the right tools.

After installing the glass, apply caulking to the edge. This will make the glass weatherproof. Install a glazier's pointing on both sides of the frame. This will help secure the pane. The points shouldn't be so tight as to cause friction between the sash and the frame however they shouldn't be loose.

Before applying the putty to the surface, gently knead it until it becomes soft and free of lumps. Roll it into pencil-sized strips. Apply the first strip to the frame's corner. Work from one corner to another and ensure that it is even and smooth.

Glazier's Points

The glazier’s points are small triangular pieces of metal that allow glass to be secured to the frame without causing any damage to the fragile surface. Understanding how to use these hidden tiny helpers is simple and could save you money on professional installation or the cost of new glass.

After the old putty and the glazier's points have been removed, thoroughly clean the frame with a utility knife to get rid of any remaining traces. Lightly sand the frame in the rabbet grooves to smooth out rough areas. If you sand wood, protect it with painter's tape to protect it from damage caused by accidental sanding.

Take measurements of the empty frame and write down accurate measurements. These dimensions can be taken to a home center or hardware store, and the new pane will be cut slightly smaller. This will ensure that the pane fits comfortably and allows for expansion and contraction.

Place the new pane in the frame and press it in place with your hand. Utilize the chisel's point or the edge of the putty blade to tap the glaziers' points as illustrated in Figure 11. When you're done, they should be flush with the top edge of the pane, and the shoulders that are raised of the points should be below the rabbet's lip. groove.

Apply a thin bead of glazing compound over the edges of the new glass and into the rabbet grooves, to seal and protect them. Allow it to dry and [Redirect-Meta-1] cure completely.

Install the new window sash when the glazing compound has dried. The first step is to coat the wood with an even layer of linseed. This will prevent the new putty from drying out or cracking when it absorbs moisture. Apply the coating using a brush this coat, or the tip of the blade. Then, use the chisel that is on the back of the putty tool or the back of the putty handle to gently smash the new sash or glazier's point into the rabbet grooves. Repeat this process at intervals of 10 inches all around the frame.

Putty

A baseball thrown at you or an unintentional rock, or falling branch could cause a window glass replacement near me to break or crack. Most windows can be replaced by simply putting in a fresh piece. The glass is held in place using tiny metal clips known as a glazier's point and putty, often called glazing compound. Before you install a new pane, first remove the old one and clean up the area with an abrasive and an abrasive scraper that is a pull type or the wood chisel. Wear protective glasses and gloves while you do this work. If the window is secured to the frame, you'll have to employ a heat gun in order to soften the adhesive before cutting it loose.

If you're planning to install the original sash, remove any pieces of molding that hold the old pane in place. Sand the sash until it's flat and ready to receive new caulk. Once the sash is installed it is possible to apply a silicone caulk over the glass. This will ensure that it won't leak over time or discolor.

Take out the glazing points in the rabbets. These are the grooves on the sash, where the glass is. If they're difficult to cut out, try holding a hand tool like a heat gun over them to soften them up first. When using a heating tool, make sure to not scratch the sash or its railings.

After the old glaze points and putty are removed, make a bed for the new pane. Roll a rope with glazing compound between your fingers and make it around 1/2 inch thick. Press it into the rabbets where the glass will be placed. It is crucial that the glass rests against the putty in all places on each side So if you have to do so, gently tap the glass into the rabbet with your thumb.

If the new pane has a crack then you can seal it with a solvent-based glue or silicone caulk prior to pressing it into the sash. Otherwise, you'll need to apply putty on the crack to create an impervious seal to keep water out. When the putty dries and the film is oily, wipe it off the glass with an abrasive and allow it to completely dry before painting. If you paint before the putty is completely dry, it won't create an effective seal and could be leaking or discoloring over time.

Paint

You might be worried about replacing a damaged piece of glass. The truth is, replacing a single pane of glass doesn't have to be costly even if you do it your own. In fact even windows with double panes can be replaced at a fraction of the cost of an expert.

If you are working with a large glass window first, ensure that it is securely attached to the frame. Using the proper tools and [Redirect-301] techniques you can make this task relatively easy and fast.

When you're ready to start with the removal of the old window pane by removing the metal glazing points that are connected to it. These are tiny metal triangles which act as "nails" that hold the window within the frame. They are placed under a glaze putty or bead that sets to form an unbreakable wedge which holds the wood frame in place and hides the points.

Once you have the old pane taken away clean the surrounding frame and wood. Scrape off any paint and sand down the rabbet grooves where the glazing points used to be. Sand them down to clean wooden surfaces, allowing you to paint the frames the same shade. After sanding the wood you can apply a layer flax oil. This will help extend its life.

Then, take measurements of the dimensions of the window opening. It is necessary to take horizontal and vertical measurements of the entire opening, and also the thickness of the old pane. Subtract 1/8 inch from each measurement to ensure you have the exact size for the new pane. This will also allow for expansion and contraction of the glass during seasonal change. Take these dimensions to your local hardware or home improvement store and ask them to cut you the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.